Flash Chromatography Products & Reviews

The one-rack Foxy R1 fraction collector can be adapted to a broad spectrum of applications. The units can distribute fractions into 96 well microplates, standard tube sizes, and bottles. For essentially unlimited volumes, funnel racks can direct fluids to any collection vessel or downstream process. 

RediSep Rf Gold C8 reversed-phase columns are packed with 20–40 µm spherical bonded silica, providing improved separation. Achieve near prep-HPLC results with greater sample recovery to easily purify up to gram-scale on your Flash system. Increased pore size optimized for purification of larger molecules like peptides and proteins.

The CombiFlash NextGen 300 is configurable to your needs. Like the 300+, safety features including active vapor, solvent level and waste-level sensing are standard. The system is designed for liquid injections, operating at up to 300 psi (20 bar).

The CombiFlash NextGen 100 offers flow rates up to 100 mL/min and operating pressures up to 150 psi (10 bar). This is an economical, basic system designed to perform both normal and reverse phase purifications.

Biotage Process-Scale Flash Purification Quickly purify multi-gram quantities of organic compound Purify up to 40 grams of compound at a rate of 250 mL/min with the Biotage Flash 75™ system, up to 75% faster than traditional glass columns. These rugged stainless steel systems safely operate at 100 psi enabling higher flow rates, purity and the use of higher viscosity solvents.

Biotage—Large Scale Flash Purification

Sfär Stands for Spherical, Biotage ® Stands for Quality 

The compact, lower capacity FC 203B Fraction Collector collects samples based on time, drop, or peak, making it a choice for a range of LC applications. The collector accommodates a wide variety of collection vessels, including microplates, vials, and tubes and can be used with any HPLC system.

The FC 204 Fraction Collector is a compact, large-bed fraction collector with a large capacity capable of handling test tubes, vials, and up to eight shallow or deep well microplates. Fractions can be collected by drop, peak, or time, and the collector can be used with any HPLC system.

The VERITY Compact LC System simplifies and streamlines compound purification by integrating preparative HPLC and flash chromatography in one customizable instrument making it one of the most flexible automated purification systems available.

Fraction Collector - 116 tube capacity for 10 to 16 mm tubes. Our fraction collector can be operated as a simple fraction collector, where each fraction is the same size and the fraction size is set in terms of time, drops, or external events (like counts from a pump). A simple command entered from the membrane keypad enables the internal peak detector. This allows you to collect only those peaks of interest from the chromato…

Reservoir at top with product standard 2 mm bore PTFE plug.

Reservoir at top with product standard 2 mm bore PTFE plug.

These PYREX chromatography reservoirs have a central cavity for a mobile phase inlet reservoir, an autoclavable plastic coat that absorbs UV up to 385nm, and a GL-45 thread finish. These may be used with our 3-hole cap #1395-3H.

This PYREX chromatography reservoirs has a central cavity for a mobile phase inlet reservoir, an autoclavable plastic coat that absorbs UV up to 385nm, and a GL-45 thread finish. This may be used with our 3-hole capCat. No. 1395-3H.

These PYREX chromatography reservoirs have a central cavity for a mobile phase inlet reservoir, an autoclavable plastic coat that absorbs UV up to 385nm, and a GL-45 thread finish. These may be used with our 3-hole cap #1395-3H.

These PYREX chromatography reservoirs have a central cavity for a mobile phase inlet reservoir, an autoclavable plastic coat that absorbs UV up to 385nm, and a GL-45 thread finish. These may be used with our 3-hole cap #1395-3H.

These 125 mL PYREX® atomizers are used for spraying reagents onto thin layer chromatography plates. They have a full length 24/40 Standard Taper joint between the reservoir and spraying device.

These 250 mL PYREX® atomizers are used for spraying reagents onto thin layer chromatography plates. They have a full length 24/40 Standard Taper joint between the reservoir and spraying device.

These tubes are designed for general chromatographic analysis. The tops are tooled for rubber stopper fit and the tubes are fabricated with sealed-in coarse porosity fritted discs. The outflow tubes are large in diameter to eliminate the smearing of the definition bands of effluent caused by the tube being filled, and the solvent mixed before being expelled. The outflow tubes are long enough to protrude through a rubber stoppe…

These tubes are designed for general chromatographic analysis. The tops are tooled for rubber stopper fit and the tubes are fabricated with sealed-in coarse porosity fritted discs. The outflow tubes are large in diameter to eliminate the smearing of the definition bands of effluent caused by the tube being filled, and the solvent mixed before being expelled. The outflow tubes are long enough to protrude through a rubber stoppe…

These tubes are designed for general chromatographic analysis. The tops are tooled for rubber stopper fit and the tubes are fabricated with sealed-in coarse porosity fritted discs. The outflow tubes are large in diameter to eliminate the smearing of the definition bands of effluent caused by the tube being filled, and the solvent mixed before being expelled. The outflow tubes are long enough to protrude through a rubber stoppe…

The 10x300mm PYREX® column is designed for general chromatographic column separations. The top is tooled for a No. 00 rubber stopper fit. A PTFE (Polytetrafluorethylene) Product Standard stopcock with a No. 2 plug is provided for better column control. Sealed into the column in a coarse porosity (40 to 60 µm) fritted disc. The volume below the disc is minimized to prevent mixing and to allow clear, sharp, band definition. For…

These 11.4L PYREX® rectangular chromatography tanks are ground to the close tolerances needed for tight cover fit. Jar edges are ground flat within 0.25mm. Covers are not supplied.Warning: Do not use with heat, pressure or vacuum applications.

These 3.8L PYREX® rectangular chromatography tanks are ground to the close tolerances needed for tight cover fit. Jar edges are ground flat within 0.25mm. Covers are not supplied.Warning: Do not use with heat, pressure or vacuum applications.